Press and hold “Lock” and “Filter” at the same time to turn off the cooling feature in the fridge and freezer. The control display will show “Cooling Off.” You can turn the cooling feature back on by pressing and holding the same buttons.
Just so, How do I fix my refrigerator that is not cooling?
Vacuum the coils under or behind the fridge. Clogged coils can cause poor cooling. Check to make sure nothing is stuck in the condenser fan and that it spins freely (models with coils on the back won’t have a fan). To do this, unplug the fridge and pull it out.
Where is the temperature control on Whirlpool refrigerator?
Similarly, How do you turn on the refrigerator cooler?
To turn cooling off:
- Press and hold the LOCK and MEASURED FILL buttons at the same time for 3 seconds. …
- Press and hold LOCK and MEASURED FILL for 3 seconds again to turn cooling back on.
How do I adjust the temperature on my Whirlpool Gold refrigerator?
What can cause a refrigerator to stop cooling?
Here are five other common reasons why your fridge may not be cooling, and how to address them.
- Condenser coils are dusty. …
- The condenser fan is broken. …
- The evaporator fan is broken. …
- Evaporator coils are covered in frost. …
- Air inlet damper is broken.
Can you reset a refrigerator by unplugging it?
By unplugging the fridge for 24 hours, the ice melts. If the fridge starts cooling again, then you have fixed the immediate problem (iced coils) and possibly identified the root cause (bad defrost controller).
Why is my fridge not getting cold but my freezer is?
When the fridge is not cold but the freezer is, the problem is probably tied to one of your refrigerator’s mechanisms not working as designed. … A small fan and motor are mounted near the evaporator, helping draw air over the coils and circulate it to the fridge and freezer.
What setting is coldest on a Whirlpool fridge?
On every fridge the rules for the coldest settings are always the following: The numbers on the fridge’s temperature dial indicate refrigerant power. The higher the number goes the colder the fridge will maintain. Setting it to 5 will make your fridge the coldest.
How long does it take for a new Whirlpool fridge to get cold?
New installation – Following installation, allow 24 hours for the refrigerator and freezer to cool completely. NOTE: Adjusting the temperature control(s) to the coldest setting will not cool either compartment (refrigerator or freezer) more quickly.
How do you check a Whirlpool refrigerator thermostat?
What does it mean when my refrigerator says cooling off?
If the Refrigerator is not cooling properly, check to make sure the Refrigerator is turned on. Some Refrigerators need to be manually turned back on after a power outage or power surge. The Refrigerator could also accidentally be turned off during routine cleaning.
Can you reset a refrigerator by unplugging it?
Unplug your refrigerator
Disconnect your fridge from its power source by removing the power cord from the wall outlet. You may hear some whooshing or knocking noises after you do so; that’s normal. Make sure your fridge stays unplugged for several minutes, otherwise the reset won’t work.
Why is my fridge not cooling but my freezer is?
When the fridge is not cold but the freezer is, the problem is probably tied to one of your refrigerator’s mechanisms not working as designed. … A small fan and motor are mounted near the evaporator, helping draw air over the coils and circulate it to the fridge and freezer.
Is 1 or 7 colder on a Whirlpool fridge?
The numbers on the fridge’s temperature dial indicate refrigerant power. The higher the number goes the colder the fridge will maintain. Setting it to 5 will make your fridge the coldest.
What temperature should a Whirlpool fridge be?
The typical factory setting for Whirlpool® refrigerators is the recommended 37°F (3°C), but temperatures on all refrigerators may need to be set higher or lower depending on your fridge’s environment and other factors. Read on to get more answers to your temperature questions.
How long should you unplug your refrigerator to reset it?
Unplug the appliance from the wall socket for 30-45 minutes, then plug it back in. This will reset the device and in some cases it may be enough to completely fix the problem. If a hard reset did not solve the problem, measure the fluid temperature.
How long do I unplug my fridge to reset it?
Does a fridge have a reset button?
Most don’t automatically reset. If the appliance has a reset button, it should just need to be held in for 30 seconds to correct the fridge. Some refrigerators, including Maytag and Amana, need to have the lock button and the reset or auto buttons held at the same time to reset the fridge.
How do I run a diagnostic on my Whirlpool refrigerator?
To start with we need to start the refrigerator’s diagnostic mode. To do this open the refrigerator door and press one or both door switches, depending on your refrigerator type. Next press the refrigerator temperature (+) button three times in ten seconds and release the light switch or switches.
What is the first thing to check when a refrigerator stops working?
If Your Fridge Has Stopped and the Light is Off
As obvious as this sounds, often a fridge shuts down completely because it’s simply getting no power. The first thing to check is the breaker (in your home’s electrical service panel) of the circuit serving the fridge.
Why is my fridge warm?
Refrigerator Is Too Full
Your refrigerator stays at the proper temperature thanks to cold air that’s consistently circulated through the appliance. If there are too many items in your fresh food compartment, that cold air may not circulate properly, resulting in a refrigerator that’s warm.
